How To Program Caddx Nx 8 Wiring

• How To Program Caddx Nx 8
• How To Program Caddx Nx 8 Wiring Instructions
• Caddx Nx 8 Programming Manual
• How To Program Caddx Nx 8 Wiring Kit
• Nx 8 Panel

Modular systems. Up to 32 modules can be added to expand the capabilities of the NX-8. ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108E LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108E 8 Zone LED Keypad NX-116E 16 Zone LED Keypad NX-124E 24 Zone LED Keypad NX-148E Alphanumeric LCD Keypad. Jason of Alarm System Store takes you through a tutorial on programming the Interlogix NetworX NX4, NX6, or NX8 alarm panels. He steps you into programming b. View and Download GE NX-1308E - Caddx 8 Zone LED Keypad installation and startup manual online. NX-1308E - Caddx 8 Zone LED Keypad control panel pdf manual download.

Modular systems. Up to 32 modules can be added to expand the capabilities of the NX-8.ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108E LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108E 8.

ARMING IN “EXIT” MODE EXIT is used when the user is away from the premises

and wants the interior protected (the motion detectors ON).

1. Close all protected doors and windows.

ARMING IN “STAY” MODE STAY is used when the user is inside the premises and

wants protection around the perimeter (the motion

detectors OFF).

2. Press the “STAY” key.

DISARMING SYSTEM Enter code.

2. Enter a master code. The “ready” light will flash.

3. Enter the 2-digit user number (example: “03” for user

4. Enter the new 4-digit user code. Note: To delete a

user code, enter * * * * for a 4-digit code.

5. The ready light will flash. If the code is rejected, the

6. If another user code needs to be programmed,

7. Press the “#” key while the ready light is flashing to

exit the User Code Programming Mode.

BYPASSING ZONES System must be in disarmed state.

2. Enter 1 or 2 digits indicating the zone you wish to

bypass. (Example: Press the “1” key for zone 1,

press “1” then “2” for zone 12.)

4. The corresponding zone light will illuminate indicating

the zone has been bypassed. Repeat steps #2 and #3 for

any other zone(s) that need to be bypassed.

5. Press the “#” key to exit the Bypass Mode. The bypass

light will stop flashing upon exiting the Bypass Mode.

All zones will automatically be unbypassed each time the

system is disarmed.

VIEW ALARM MEMORY 1. Press “8” “3.” The zone(s) that created the last alarm

2. The ALARM MEMORY feature will flash those zones

that created alarms and will light steady those zones that

were bypassed during the last alarm.

IDENTIFYING TROUBLES

FLASHING ARMED LIGHT The armed light will flash when there has been

an alarm during the previous arm cycle.

POWER LIGHT OFF No AC power.

POWER LIGHT FLASHING Low system battery.

FIRE LIGHT FLASHING Trouble with fire device or wiring.

ZONE LIGHT FLASHING RAPIDLY A zone is in a trouble condition.

How To Program Caddx Nx 8

SERVICE LIGHT IS ON Press “*2” for further information (indicated by

zone lights).

Zone 1 – System fault.

Zone 2 – Zone tamper.

Zone 5 – Zone trouble.

Zone 6 – Telephone trouble.

Zone 7 – Dialer failure.

How To Program Caddx Nx 8 Wiring Instructions

Zone 8 – System lost time.

Enter “#” to exit mode.

ENTER CODE TO SILENCE TROUBLE BEEPS.

ENTER “*7” TO ATTEMPT TO RESET TROUBLES.

Caddx Nx 8 Programming Manual

ENTER CODE TO CLEAR SERVICE LIGHT AFTER A PHONE TROUBLE HAS BEEN CLEARED.

How To Program Caddx Nx 8 Wiring Kit

SET CLOCK 1. Press “*97.”

Nx 8 Panel

3. Enter time as 4-digit military time.